Cisco 6506-E Switch Açılış Problemi
CLI Guru - Cisco Eğitim ve Danışmanlık Merkezi |

2007 yılından bu yana aktif olan ciscotr.com, kısa bir süre sonra " www.bilisim.pro " olarak devam edecektir.  
Mevcut mesajlarınız ve kullanıcı bilgilerinizle yenilenen sitemizde katılıma devam edebileceksiniz.

+ Konuyu Cevapla
Toplam 10 sonuçtan 1 ile 10 arasındakiler gösteriliyor.
Cisco 6506-E Switch Açılış Problemi

Merhaba arkadaşlar; Elimizde boşta olan bir Cisco 6506-E ve üzerinde Supervisor, ACE ve firewall modülleri var. Bunu sıfırlamak için erase nvram gibi komutlar flan girdik ve sanırım flash kartının içindeki

  1. #1
    crimson isimli Üye şimdilik offline konumundadır Member
    Üyelik tarihi
    Oct 2009
    Mesajlar
    30

    Standart Cisco 6506-E Switch Açılış Problemi

    Merhaba arkadaşlar;

    Elimizde boşta olan bir Cisco 6506-E ve üzerinde Supervisor, ACE ve firewall modülleri var.

    Bunu sıfırlamak için erase nvram gibi komutlar flan girdik ve sanırım flash kartının içindeki image'larıda sildik gibi. Cihazın açılıştaki logları aşağıda, bu durumu nasıl düzeltebiliriz.

    Teşekür ederim.

    Kod:
    00:03:18: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimal Diagnostics...
    00:03:21: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
    00:03:29: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
    00:06:14: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
    00:06:14: SP: ******************************************************************
    00:06:14: SP: * WARNING:
    00:06:14: SP: * EOBC Stress Ping test on module 3 may take up to 3min.
    00:06:14: SP: * During this time, please DO NOT perform packet switching on the module.
    00:06:14: SP: ******************************************************************
    
    00:06:22: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
    00:06:22: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics
    00:06:22: %OIR-SP-6-INSCARD: Card inserted in slot 3, interfaces are now online
    System Bootstrap, Version 8.4(2) Release
    Copyright (c) 1994-2005 by cisco Systems, Inc.
    Cat6k-Sup720/SP processor with 524288 Kbytes of main memory
    
    Autoboot: failed, BOOT string is empty
    Autoboot executing command: "boot "
    
    Initializing ATA monitor library...
    string is bootdisk:s72033-ipservicesk9-mz.122-18.SXF9.bin
    Loading image, please wait ...
    
    
    Initializing ATA monitor library...
    
    Self extracting the image... [OK]
    Self decompressing the image : #################################################################################################### [OK]
    
                  Restricted Rights Legend
    
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    
    
    
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:34 by kellythw
    Image text-base: 0x40101040, data-base: 0x4146B340
    
    
    00:00:03: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    
    00:00:03: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
    
    00:00:04: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    
    00:00:03: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    00:00:04: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
    
    
    
    System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2005 by cisco Systems, Inc.
    Cat6k-Sup720/RP platform with 524288 Kbytes of main memory
    
    Download Start
    !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    Download Completed! Booting the image.
    Self decompressing the image : ################################################################################################################################################################################################################ [OK]
    
                  Restricted Rights Legend
    
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    
    
    
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:25 by kellythw
    Image text-base: 0x40101040, data-base: 0x42DAF270
    
    
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    
    If you require further assistance please contact us by sending email to
    [email protected]
    
    cisco WS-C6506-E (R7000) processor (revision 1.1) with 458720K/65536K bytes of memory.
    Processor board ID SAL1129UVJ2
    SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
    Last reset from s/w reset
    SuperLAT software (copyright 1990 by Meridian Technology Corp).
    X.25 software, Version 3.0.0.
    Bridging software.
    TN3270 Emulation software.
    1 Virtual Ethernet/IEEE 802.3 interface
    56 Gigabit Ethernet/IEEE 802.3 interfaces
    1 Ten Gigabit Ethernet/IEEE 802.3 interface
    1917K bytes of non-volatile configuration memory.
    8192K bytes of packet buffer memory.
    
    65536K bytes of Flash internal SIMM (Sector size 512K).
    %Error opening tftp://255.255.255.255/network-confg (Socket error)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
    SETUP: new interface Vlan1 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/1 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/2 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/3 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/4 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/5 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/6 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/7 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/8 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/9 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/10 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/11 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/12 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/13 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/14 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/15 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/16 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/17 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/18 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/19 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/20 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/21 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/22 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/23 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/24 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/25 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/26 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/27 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/28 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/29 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/30 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/31 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/32 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/33 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/34 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/35 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/36 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/37 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/38 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/39 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/40 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/41 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/42 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/43 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/44 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/45 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/46 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/47 placed in "shutdown" state
    SETUP: new interface GigabitEthernet2/48 placed in "shutdown" state
    SETUP: new interface GigabitEthernet5/1 placed in "shutdown" state
    SETUP: new interface GigabitEthernet5/2 placed in "shutdown" state
    
    
    Press RETURN to get started!
    
    
    00:00:51: curr is 0x0
    
    00:00:51: RP: Currently running ROMMON from S (Gold) region
    00:01:18: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/network-confg) failed
    00:01:18: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed
    00:01:26: %SYS-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:25 by kellythw
    00:01:26: %SYS-6-BOOTTIME: Time taken to reboot after reload = 133147329 seconds
    00:00:03: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    00:00:04: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
    
    
    
    00:00:04: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    
    Firmware compiled 20-Feb-07 14:12 by integ Build [100]
    
    
    00:01:01: SP: SP: Currently running ROMMON from S (Gold) region
    00:01:27: %SYS-SP-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:34 by kellythw
    00:01:28: %OIR-SP-6-INSPS: Power supply inserted in slot 1
    00:01:28: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
    00:01:28: %OIR-SP-6-INSPS: Power supply inserted in slot 2
    00:01:28: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
    00:01:28: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy mode, system is operating on both power supplies.
    00:01:31: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.
    00:01:31: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
    00:01:32: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics...
    00:01:53: %DIAG-SP-6-DIAG_OK: Module 5: Passed Online Diagnostics
    00:01:53: %OIR-SP-6-INSCARD: Card inserted in slot 5, interfaces are now online
    00:01:54: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...
    00:02:03: %MFIB_CONST_RP-6-REPLICATION_MODE_CHANGE: Replication Mode Change Detected. Current system replication mode is Ingress
    00:02:02: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics
    00:02:03: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online
    00:03:18: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimal Diagnostics...
    00:03:21: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
    00:03:30: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
    00:06:16: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
    00:06:16: SP: ******************************************************************
    00:06:16: SP: * WARNING:
    00:06:16: SP: * EOBC Stress Ping test on module 3 may take up to 3min.
    00:06:16: SP: * During this time, please DO NOT perform packet switching on the module.
    00:06:16: SP: ******************************************************************
    
    00:06:24: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
    00:06:24: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics

  2. #2
    hb1989 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Apr 2011
    Mesajlar
    281

    Standart

    Makina boot yaparken, bu noktadayken "%OIR-SP-6-CONSOLE: Changing console ownership to route processor" terminal programindan "BREAK" sinyali yolla makinaya. ROMMON moduna gecersin ve sürekli boot etmeyi birakiyor. PC de ftp/tftp calistirip, rommon dan saglam bi IOS i switch in flashine yükle.

    Fakat ondan önce, yani IOS i yüklemeden önce, rommon dan bakabilirsin, makinanin hangi kartlarda IOS ler mevcut diye.

    dir slot0:
    dir disk0:
    dir sup-bootflash:
    dir sup-bootdisk:
    dir flash:

    Ve boot sup-bootflash:<IOS-name> ilede makinayi calisan bi IOS ile boot edebilirsin.

    Yada en basit yolu, supervisor modulundeki Compact Flash (CF) kartini cikartip kart okuyucudan PC ye baglayip, saglam bi IOS atip makinaya tekrar takip calistirabilirsin.

  3. #3
    crimson isimli Üye şimdilik offline konumundadır Member
    Üyelik tarihi
    Oct 2009
    Mesajlar
    30

    Standart

    selam hb1989


    dediklerini denedim fakat olmadı, cihaz aşağıdaki şekilde açılıyor, fakat sorun hala devam ediyor.
    başka ne yapabilirim.
    Aynı model bir başka cihaz var üzerlerinde flash card yok ama.

    birde cihaz açıldıktan sonra: aşağıdaki dosyalar var.

    6500#dir
    Directory of sup-bootdisk:/

    1 -rw- 42895364 Jul 18 2007 04:46:04 +00:00 s72033-ipservicesk9-mz.122-18.SXF9.bin
    2 -rw- 15972 Apr 27 2010 13:50:08 +00:00 27.04.2010-conf
    3 -rw- 32357195 Dec 3 2010 10:03:26 +00:00 c6ace-t1k9-mz.A2_3_2.bin







    Kod:
    rommon 1 > dir slo
    bad device name (device not supported) 
    usage: dir <device>
    rommon 2 > dir slot0:
    
    monitor: command "dir" not found
    rommon 3 > dir disk0:
    
    monitor: command "dir" not found
    rommon 4 > dir sup-bootflash:
    bad device name (device not supported) 
    usage: dir <device>
    rommon 5 > dir sup-bootdisk:
    bad device name (device not supported) 
    usage: dir <device>
    rommon 6 > dir flash:
    bad device name (device not supported) 
    usage: dir <device>
    rommon 7 > dir ?
    bad device name (device not supported) 
    usage: dir <device>
    rommon 8 > dir slot0:
    bad device name (device not supported) 
    usage: dir <device>
    rommon 9 >  
    rommon 10 > 
    rommon 10 > 
    rommon 10 > 
    rommon 10 > reset
    
    System Bootstrap, Version 8.4(2) Release
    Copyright (c) 1994-2005 by cisco Systems, Inc.
    Cat6k-Sup720/SP processor with 524288 Kbytes of main memory
    
    Autoboot: failed, BOOT string is empty
    Autoboot executing command: "boot "
    
    Initializing ATA monitor library...
    string is bootdisk:s72033-ipservicesk9-mz.122-18.SXF9.bin
    Loading image, please wait ...
    
    
    Initializing ATA monitor library...
    
    Self extracting the image... [OK]
    Self decompressing the image : #################################################################################################### [OK]
    
                  Restricted Rights Legend
    
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    
    
    
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:34 by kellythw
    Image text-base: 0x40101040, data-base: 0x41460C30
    
    
    00:00:04: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    
    00:00:04: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
    
    00:00:05: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    
    00:00:04: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    00:00:05: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
    
    
    
    System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2005 by cisco Systems, Inc.
    Cat6k-Sup720/RP platform with 524288 Kbytes of main memory
    
    Download Start
    !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    Download Completed! Booting the image.
    Self decompressing the image : ################################################################################################################################################################################################################ [OK]
    
                  Restricted Rights Legend
    
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    
    
    
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:25 by kellythw
    Image text-base: 0x40101040, data-base: 0x42DAC250
    
    
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    
    If you require further assistance please contact us by sending email to
    [email protected]
    
    cisco WS-C6506-E (R7000) processor (revision 1.1) with 458720K/65536K bytes of memory.
    Processor board ID SAL1129UVJ2
    SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
    Last reset from s/w reset
    SuperLAT software (copyright 1990 by Meridian Technology Corp).
    X.25 software, Version 3.0.0.
    Bridging software.
    TN3270 Emulation software.
    1 Virtual Ethernet/IEEE 802.3 interface
    56 Gigabit Ethernet/IEEE 802.3 interfaces
    1 Ten Gigabit Ethernet/IEEE 802.3 interface
    1917K bytes of non-volatile configuration memory.
    8192K bytes of packet buffer memory.
    
    65536K bytes of Flash internal SIMM (Sector size 512K).
    Warning: enabling multiple VLAN interfaces may result in traffic bypassing the ACE Module - use with caution!
    Warning: enabling multiple VLAN interfaces may result in traffic bypassing the FWSM - use with caution!
    
    
    Press RETURN to get started!
    
    
    00:00:52: curr is 0x0
    
    00:00:52: RP: Currently running ROMMON from S (Gold) region
    00:01:04: %SVCLC-5-SVCLCMULTI: Group 1 being tied to more than one module
    00:01:04: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
    00:01:05: %SYS-5-CONFIG_I: Configured from memory by console
    00:01:07: %SYS-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:25 by kellythw
    00:01:07: %SYS-6-BOOTTIME: Time taken to reboot after reload = 133153729 seconds
    00:01:07: %MFIB_CONST_RP-6-REPLICATION_MODE_CHANGE: Replication Mode Change Detected. Current system replication mode is Ingress
    00:00:04: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    00:00:05: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
    
    
    
    00:00:05: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
    
    
    Firmware compiled 20-Feb-07 14:12 by integ Build [100]
    
    
    00:01:01: SP: SP: Currently running ROMMON from S (Gold) region
    00:01:04: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
    00:01:07: %SYS-SP-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software 
    IOS (tm) s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Wed 16-May-07 23:34 by kellythw
    00:01:09: %OIR-SP-6-INSPS: Power supply inserted in slot 1
    00:01:09: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
    00:01:09: %OIR-SP-6-INSPS: Power supply inserted in slot 2
    00:01:09: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
    00:01:09: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy mode, system is operating on both power supplies.
    00:01:16: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.
    00:01:16: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
    00:01:18: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics...
    00:01:39: %DIAG-SP-6-DIAG_OK: Module 5: Passed Online Diagnostics
    00:01:39: %OIR-SP-6-INSCARD: Card inserted in slot 5, interfaces are now online
    00:01:40: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...
    00:01:48: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics
    00:01:49: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online
    00:01:54: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks
    00:03:04: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimal Diagnostics...
    00:03:07: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
    00:03:16: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
    00:05:55: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
    00:05:55: SP: ******************************************************************
    00:05:55: SP: * WARNING:
    00:05:55: SP: * EOBC Stress Ping test on module 3 may take up to 3min.
    00:05:55: SP: * During this time, please DO NOT perform packet switching on the module.
    00:05:55: SP: ******************************************************************
    
    00:06:03: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
    00:06:03: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics
    00:06:03: %OIR-SP-6-INSCARD: Card inserted in slot 3, interfaces are now online
    00:06:10: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks
    Konu crimson tarafından (06.10.2011 Saat 17:52 ) değiştirilmiştir.

  4. #4
    hb1989 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Apr 2011
    Mesajlar
    281

    Standart

    Büyük ihtimal ACE modulün dosyasi silinmis. ACE modülü sök, ve makinayi yeniden boot yap. Normal acilacaktir.

    Bu linkte ACE modulün ayarlarini nasil yapacagin ayrintili bi sekilde anlatiliyor. Ama dedigim gibi, önce ACE modülü cikart, makinayi boot et.

    Cisco Application Control Engine (ACE) Troubleshooting Guide -- Troubleshooting ACE Boot Issues - DocWiki

  5. #5
    crimson isimli Üye şimdilik offline konumundadır Member
    Üyelik tarihi
    Oct 2009
    Mesajlar
    30

    Standart

    Dediğim gibi cihaz açılıyor, fakat bolca hata vererek açılıyor, bunun sebebide benim tabi

    cihaz açıldıktan sonra ace girebiliyorum, ace çalışıyor. bu sorunlar başlamadan önce girdiğim komutları buldum,

    Bu durumu nasıl düzeltebilirim?

    Kod:
    6500#erase /all nvram: 
    Erasing the nvram filesystem will remove all files! Continue? [confirm]
    [OK]
    Erase of nvram: complete
    
    6500#erase startup-config 
    Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
    [OK]
    Erase of nvram: complete
    6500#
    
    6500#erase nvram:
    Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
    [OK]
    Erase of nvram: complete
    
    6500#delete nvram:startup-config
    Delete filename [startup-config]? 
    Delete nvram:startup-config? [confirm]
    
    6500#erase /all nvram: 
    Erasing the nvram filesystem will remove all files! Continue? [confirm]
    [OK]
    Erase of nvram: complete
    6500#

  6. #6
    hb1989 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Apr 2011
    Mesajlar
    281

    Standart

    Cihazin hata vermesi, ACE nin kendi dosyasini bulamamasi.

    Diger makinadan ACE dosyasini herhangi bi CF karta kopyala, CF karti makinaya tak. Sonrada ACE nin acilisi icin gerekli boot komutlari gir.

    boot system image:c6ace-t1k9-mzg.3.0.0_A2_2.0.bin

  7. #7
    crimson isimli Üye şimdilik offline konumundadır Member
    Üyelik tarihi
    Oct 2009
    Mesajlar
    30

    Standart

    hb1989 yalnız cihaz üzerinde dir yaptığımda ace dosyası gözüküyor, bulamadığı dosya bu mu?

    6500#dir
    Directory of sup-bootdisk:/

    1 -rw- 42895364 Jul 18 2007 04:46:04 +00:00 s72033-ipservicesk9-mz.122-18.SXF9.bin
    2 -rw- 15972 Apr 27 2010 13:50:08 +00:00 27.04.2010-conf
    3 -rw- 32357195 Dec 3 2010 10:03:26 +00:00 c6ace-t1k9-mz.A2_3_2.bin

  8. #8
    hb1989 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Apr 2011
    Mesajlar
    281

    Standart

    Cisco startup configleri nvram de yedekler. startup config icindede, makinanin acilirken kullanmasi gereken komutlar vardir. Sen erase /all nvram le, nvram da bulunan tüm dosyalari silmissin, dogal olarak startup-config ide silmissin.
    Dogal olarakta, makina acilirken, ACE acilisi icin gereken boot statment i bulamiyor. Senin yapacagin, ACE acilirken dosyayi nerden alacagini sisteme tanitmak.

    Direkt console kabloyu ACE ye baglayabilirsin, yada bu sekilde switchin Supervisor üzerinden ACE ye baglanabilirsin;

    session slot 5 processor 0 --> 5 ACE modulün takili oldugu slot numarasi. Bu sekilde ACE modulün CLI ina gecis yapiyorsun.

    ACE cli a gecincede bu komutlari giriyorsun.

    boot system image:c6ace-t1k9-mz.A2_3_2.bin --> bu komutu girip, write yap, sonra reload edip, tekrar test edebilirsin.

    ACE rommon da takili kaliyordur büyük ihtimal, dosyanin yerini bilmedigi icin. Rommon dada bu komutu gir;
    boot=sup-bootdisk:c6ace-t1k9-mz.A2_3_2.bin
    sync

    tamamdir.

  9. #9
    gandalf_3466 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Sep 2007
    Mesajlar
    264

    Standart

    Merhaba arkadaslar,

    Elimde su anda 6506e icersinde sifresine recovery yapmaya calistigim bir SUP32-GE-3B line card var. Asagida ki linkte ki islem,leri yapmama ragmen sifreyi kaldiramadim.

    Recovering a Catalyst 6500/6000 Running Cisco IOS System Software from a Corrupted or Missing Boot Loader Image or ROMmon Mode - Cisco Systems


    Confreg 0x2102-->0x2142 cevirdim yine olmadi hatta

    Rom monitor deyken confreg ile su sekilde yapmama ragmen sonuc vermedi.


    Kod:
    System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1)
    Technical Support: Support and Documentation - Cisco Systems
    Copyright (c) 2004 by cisco Systems, Inc.
    Cat6k-Sup32 platform with 524288 Kbytes of main memory
    
    Autoboot executing command: "boot bootdisk:"
    
    
    monitor: command "boot" aborted due to user interrupt
    
    
    Exit at the end of BOOT string
    rommon 1 >
    rommon 1 > confreg
    
               Configuration Summary
       (Virtual Configuration Register: 0x10f)
    enabled are:
     [ 0 ] console baud: 9600
     boot: ...... image specified by the boot system commands or default to: cisco17                                                                                                                                                             -Cat6k-Sup32
    
    do you wish to change the configuration? y/n  [n]:  y
     enable  "diagnostic mode"? y/n  [n]:  n
     enable  "use net in IP bcast address"? y/n  [n]:  n
     enable  "load rom after netboot fails"? y/n  [n]:  n
     enable  "use all zero broadcast"? y/n  [n]:  n
     enable  "break/abort has effect"? y/n  [n]:  n
     enable  "ignore system config info"? y/n  [n]:  y
     change console baud rate? y/n  [n]:  n
    change the boot characteristics? y/n  [n]:  n
    
               Configuration Summary
       (Virtual Configuration Register: 0x14f)
    enabled are:
     [ 0 ] ignore system config info
     [ 1 ] console baud: 9600
     boot: ...... image specified by the boot system commands or default to: cisco17                                                                                                                                                             -Cat6k-Sup32
    
    do you wish to change the configuration? y/n  [n]:  n
    
    
    You must reset or power cycle for new config to take effect
    rommon 2 >boot
    
    string is bootdisk:cat6000-sup32pfc3k9.8-4-6.bin
    Self decompressing the image : ############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################### [OK]
    
    System Power On Diagnostics
    DRAM Size ..........................512 MB
    Testing DRAM .......................Passed
    Verifying Text Segment .............Passed
    NVRAM Size .........................2048 KB
    Level2 Cache .......................Present
    Level3 Cache .......................Absent
    System Power On Diagnostics Complete
    Currently running ROMMON from S (Gold) region
    Boot image: bootdisk:cat6000-sup32pfc3k9.8-4-6.bin
    
    Firmware compiled 22-Aug-06 15:44 by integ Build [100]
    
    Running System Diagnostics from this Supervisor (Module 6)
    This may take several minutes....please wait
    IP address for Catalyst not configured
    DHCP/BOOTP will commence after the ports are online
    Ports are coming online ...
    WARNING: This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and use.
    Delivery of Cisco cryptographic products does not imply third-party authority
    to import, export, distribute or use encryption. Importers, exporters,
    distributors and users are responsible for compliance with U.S. and local
    country laws. By using this product you agree to comply with applicable
    laws and regulations. If you are unable to comply with U.S. and local laws,
    return this product immediately.
     
    Cisco Systems Console
     
    2012 Aug 30 04:56:58 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6
    2012 Aug 30 04:57:01 %SYS-2-PS_FAIL:Power supply 2 failed
    2012 Aug 30 04:57:01 %SYS-1-SYS_ENABLEPS: Power supply 1 enabled
    2012 Aug 30 04:57:05 %SYS-5-MOD_PWRON:Module 1 powered up
    
    Enter password:
    
    2012 Aug 30 04:57:06 %SYS-5-MOD_PWRON:Module 3 powered up
    Console> 2012 Aug 30 04:57:12 %MLS-5-MCAST_STATUS:IP Multicast Multilayer Switching is enabled
    2012 Aug 30 04:57:23 %SYS-5-MOD_OK:Module 6(WS-SUP32-GE-3B,xxxxxxxxxxxxx) is online
    2012 Aug 30 04:57:23 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6
    2012 Aug 30 04:57:33 %SYS-5-MOD_OK:Module 1(WS-X6408A-GBIC,xxxxxxxxxxxxx) is online
    2012 Aug 30 04:57:33 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 1
    2012 Aug 30 04:57:42 %SYS-5-MOD_OK:Module 3(WS-X6148-RJ-45,xxxxxxxxxxxxx) is online
    2012 Aug 30 04:57:42 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 3
    
    Enter password: 2012 Aug 30 04:58:11 %SYS-5-MOD_OK:Module 16(WS-F6K-MSFC2A,xxxxxxxxxxxxxx) is online
    Session Disconnected...
    
    Cisco Systems Console           Thu Aug 30 2012, 04:58:20
    
    Enter password:
    Enter password:
    
    Console> (enable)
    Boot etmeme ragmen yine exec mode gecmeden password istiyor 3 kere girince de

    Console (enable) moda dusuyor.

    Ayrica varolan dosya ise

    Kod:
    Console> (enable) dir all
          2   -rw-   9490452    Jun 20 2007 09:21:04 cat6000-sup32pfc3k9.8-4-6.bin

  10. #10
    gandalf_3466 isimli Üye şimdilik offline konumundadır Senior Member
    Üyelik tarihi
    Sep 2007
    Mesajlar
    264

    Standart

    Hatta su sekilde bootdisk in nerde oldugu goremedigim bir problemim var

    Kod:
    rommon 1 > set
    PS1=rommon ! >
    LOG_PREFIX_VERSION=1
    SLOTCACHE=
    SUPW_6=1
    RET_2_RTS=15:34:00 UTC Sat Jun 16 2007
    TYFIB_BLOCK_ALLOC=
    BSI=0
    RET_2_RCALTS=
    SUPW_5=1
    ACL_DENY=0
    PF_REDUN_CRASH_COUNT=0
    IMAGEVER=0
    ?=0
    BOOT=bootdisk:,1;
    CONFIG_FILE=bootdisk:switch.cfg
    PROFILE_FILE=
    
    
    rommon 2 > dir disk0:
    PCMCIA slot0 device is not initialized
    open: read error...requested 0x4 bytes, got 0x0
    trouble reading device magic number
    dir: cannot open device "disk0:"
    rommon 3 >
    
    rommon 4 > dev
    Devices in device table:
            id  name
     bootdisk:  boot flash
        disk0:  ATA slot 0
     bootdisk:  ATA slot 1
        eprom:  eprom
    rommon 5 > dir bootdisk:
    Directory of bootdisk:
    
    2      9490452   -rw-     cat6000-sup32pfc3k9.8-4-6.bin

+ Konuyu Cevapla

Bu Konuyu Paylaşın !

Bu Konuyu Paylaşın !

Yetkileriniz

  • Konu Acma Yetkiniz Yok
  • Cevap Yazma Yetkiniz Yok
  • Eklenti Yükleme Yetkiniz Yok
  • Mesajınızı Değiştirme Yetkiniz Yok