Evet, baglayabilirsiniz. Bunun için F/R switching yapmaniz gerekir. Ayrica DTE-DCE kablo kullanmaniz gerekecek. Bunun için, normal bir F/R konfig. yapin, sadece DCE kablonun bagli oldugu router uzerinde digerinden farkli birkac komut kullanmaniz gerekecek. İlgili konfigler ektedir.

Kolay Gelsin,
Hilmiye


-----Original Message-----
From: [email][email protected][/email] [mailto:[email protected]] On Behalf Of Bilal Tas
Sent: Thursday, June 16, 2005 2:12 PM
To: [email][email protected][/email]
Subject: [cisco-ttl] 2 router serial interface'den baðlama


Merhaba
2 adet router'ý lokalde serial interface'den modem olmadan baðlayýp çalýþtýrabilirmiyiz.
Bununla ilgili örnek var mý elinizde.

---------

test1#sh run
Building configuration...

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname test1
!
!
!
!
!
!
ip subnet-zero
!
frame-relay switching
!
!
process-max-time 200
!
interface Ethernet0
no ip address
no ip directed-broadcast
shutdown
!
interface Serial1
no ip address
no ip directed-broadcast
encapsulation frame-relay
clockrate 128000
cdp enable
frame-relay lmi-type ansi
frame-relay intf-type dce
!
interface Serial1.1 point-to-point
ip address x.x.x.x
no ip directed-broadcast
frame-relay interface-dlci 16
!
ip classless
no ip http server
!
!
line con 0
transport input none
line vty 0 4
login
!
end

test1#sh int s0
Serial0 is up, line protocol is up
Hardware is QUICC Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF, loopback not set
Keepalive set (10 sec)
LMI enq sent 13, LMI stat recvd 0, LMI upd recvd 0
LMI enq recvd 55, LMI stat sent 55, LMI upd sent 0, DCE LMI up
LMI DLCI 0 LMI type is ANSI Annex D frame relay DCE
Broadcast queue 0/64, broadcasts sent/dropped 23/0, interface broadcasts 3
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:14:06
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/2/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
4470 packets input, 459397 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
4516 packets output, 461634 bytes, 0 underruns
0 output errors, 0 collisions, 8 interface resets
0 output buffer failures, 0 output buffers swapped out
14 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

test1#sh frame pvc

PVC Statistics for interface Serial0 (Frame Relay DCE)

Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0

DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1

input pkts 4415 output pkts 4463 in bytes 458627
out bytes 462566 dropped pkts 0 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 23 out bcast bytes 7424
pvc create time 00:14:12, last time pvc status changed 00:09:06
test1#ping 192.168.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/75/80 ms
test1#
----------

test2#sh int s0
Serial0 is up, line protocol is up
Hardware is QUICC Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY IETF, loopback not set, keepalive set (10 sec)
LMI enq sent 54, LMI stat recvd 32, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 10/0, interface broadcasts 2
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 4 packets/sec
5 minute output rate 1000 bits/sec, 3 packets/sec
4408 packets input, 454826 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
4417 packets output, 455369 bytes, 0 underruns
0 output errors, 0 collisions, 10 interface resets
0 output buffer failures, 0 output buffers swapped out
21 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

test2# sh frame pvc

PVC Statistics for interface Serial0 (Frame Relay DTE)

DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.1

input pkts 4398 output pkts 4383 in bytes 455326
out bytes 456627 dropped pkts 0 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 10 out bcast bytes 3488
pvc create time 00:10:39, last time pvc status changed 00:05:17
test2#sh run
Building configuration...

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname test2
!
!
ip subnet-zero
!
!
!
interface Ethernet0
no ip address
no ip directed-broadcast
shutdown
!
interface Serial0
no ip address
no ip directed-broadcast
encapsulation frame-relay IETF
logging event subif-link-status
logging event dlci-status-change
no fair-queue
frame-relay lmi-type ansi
!
interface Serial0.1 point-to-point
ip address x.x.x.x
no ip directed-broadcast
frame-relay interface-dlci 16
!
ip classless
!
!
line con 0
transport input none
line vty 0 4
login
!
end

test2#