Cisco 2500 Router, Flash Size Exceded
CLI Guru - Cisco Eğitim ve Danışmanlık Merkezi |

+ Konuyu Cevapla
Toplam 2 sonuçtan 1 ile 2 arasındakiler gösteriliyor.
Cisco 2500 Router, Flash Size Exceded

Burak Bey yardımlarınız için cok tesekkur ederim. Sorun giderildi. --- "Burak Ergun (bergun)" <[email protected]: IOS version ile ilgili olabilir aşağıdaki stepler ile yapmayı deneyebilirsin. Step 1 Log into the router

  1. #1
    Burak Ergun \(bergun\) Guest

    Standart Cisco 2500 Router, Flash Size Exceded

    Burak Bey yardımlarınız için cok tesekkur ederim.
    Sorun giderildi.

    --- "Burak Ergun (bergun)" <[email protected]:

    IOS version ile ilgili olabilir
    aşağıdaki stepler ile yapmayı deneyebilirsin.

    Step 1 Log into the router via the console port using Telnet or terminal emulation software. (If you
    use terminal emulation software, configure the software settings to 9600 baud, no parity, 8 data
    bits, and 1 stop bit.)

    Step 2 When the router boots up, enter the enable mode, as follows:
    routerenable

    password: <password
    router#

    Step 3 Erase the contents of the Flash memory partition except the one currently in use (this
    partition will be in the Read ONLY state in the partition listing), as shown below.
    router# erase flash

    Partition Size Used Free Bank-Size
    State Copy Mode
    1 8192K 3724K 4467K 8192K
    Read ONLY RXBOOT-manual
    2 8192K 3724K 4467K 8192K
    Read/Write Direct

    System flash directory, partition 2:
    File Length Name/status
    1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608
    total]

    Erase flash device, partition 2? [confirm]
    Are you sure? [yes/no]: y

    Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
    ...erased

    router#

    Note If you have more than two Flash memory partitions, you must perform the previous step for
    each of the partitions to be erased.

    Step 4 Enter the show flash command to verify that the desired Flash memory partitions have been
    erased:
    router# show flash

    System flash directory, partition 1:
    File Length Name/status
    1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608
    total]
    8192K bytes of processor board System flash (Read
    ONLY)


    System flash directory, partition 2:
    No files in System flash
    [0 bytes used, 8388608 available, 8388608 total]
    8192K bytes of processor board System flash
    (Read/Write)

    You are now ready to unpartition the Flash memory.
    Step 5 Enter the configuration mode and enter the partition command to create a single Flash memory
    partition, as follows:
    router# configure terminal

    Enter configuration commands, one per line. End
    with cntrl/z.
    router(config)# partition flash 1


    Step 6 Exit the configuration mode and verify that flash memory now has a single partition, as follows:
    router(config)# exit




    -----Original Message-----
    From: Emre BALCI [mailto:[email protected]]
    Sent: 01 February 2005, Tuesday 12:11
    To: [email][email protected][/email]
    Subject: RE: [cisco-ttl] flash yukleme sorunu


    partition flash 1 16 yaziyorum requested partitioning cannot be done hatası
    alıyorum

    --- "Burak Ergun (bergun)" <[email protected]:


    Global configuration prompt'da "partition flash: 1 16 " komutunu kullanıp tek partition yapabilirsin

    -----Original Message-----
    From: Emre BALCI [mailto:[email protected]]
    Sent: 01 February 2005, Tuesday 11:18
    To: [email][email protected][/email]
    Subject: [cisco-ttl] flash yukleme sorunu


    Selamlar...
    Cisco 2500 Router 16 mb flash lı bir router a bir ios yukleyecem yaklasık
    12 mb fakat flash 8 li 2 partitiondan olusuyor gorunuyor yuklerken flash size exceded hatası alıyorum ne
    yapabilirim ?

  2. #2
    Emre BALCI Guest

    Standart RE: flash yukleme sorunu

    Burak Bey yardımlarınız için cok tesekkur ederim.
    Sorun giderildi.

    --- "Burak Ergun (bergun)" <[email protected]:

    IOS version ile ilgili olabilir
    aşağıdaki stepler ile yapmayı deneyebilirsin.

    Step 1 Log into the router via the console port using Telnet or terminal emulation software. (If you
    use terminal emulation software, configure the software settings to 9600 baud, no parity, 8 data
    bits, and 1 stop bit.)

    Step 2 When the router boots up, enter the enable mode, as follows:
    routerenable

    password: <password
    router#

    Step 3 Erase the contents of the Flash memory partition except the one currently in use (this
    partition will be in the Read ONLY state in the partition listing), as shown below.
    router# erase flash

    Partition Size Used Free Bank-Size
    State Copy Mode
    1 8192K 3724K 4467K 8192K
    Read ONLY RXBOOT-manual
    2 8192K 3724K 4467K 8192K
    Read/Write Direct

    System flash directory, partition 2:
    File Length Name/status
    1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608
    total]

    Erase flash device, partition 2? [confirm]
    Are you sure? [yes/no]: y

    Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
    ...erased

    router#

    Note If you have more than two Flash memory partitions, you must perform the previous step for
    each of the partitions to be erased.

    Step 4 Enter the show flash command to verify that the desired Flash memory partitions have been
    erased:
    router# show flash

    System flash directory, partition 1:
    File Length Name/status
    1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608
    total]
    8192K bytes of processor board System flash (Read
    ONLY)


    System flash directory, partition 2:
    No files in System flash
    [0 bytes used, 8388608 available, 8388608 total]
    8192K bytes of processor board System flash
    (Read/Write)

    You are now ready to unpartition the Flash memory.
    Step 5 Enter the configuration mode and enter the partition command to create a single Flash memory
    partition, as follows:
    router# configure terminal

    Enter configuration commands, one per line. End
    with cntrl/z.
    router(config)# partition flash 1


    Step 6 Exit the configuration mode and verify that flash memory now has a single partition, as follows:
    router(config)# exit




    -----Original Message-----
    From: Emre BALCI [mailto:[email protected]]
    Sent: 01 February 2005, Tuesday 12:11
    To: [email][email protected][/email]
    Subject: RE: [cisco-ttl] flash yukleme sorunu


    partition flash 1 16 yaziyorum requested partitioning cannot be done hatası
    alıyorum

    --- "Burak Ergun (bergun)" <[email protected]:


    Global configuration prompt'da "partition flash: 1 16 " komutunu kullanıp tek partition yapabilirsin

    -----Original Message-----
    From: Emre BALCI [mailto:[email protected]]
    Sent: 01 February 2005, Tuesday 11:18
    To: [email][email protected][/email]
    Subject: [cisco-ttl] flash yukleme sorunu


    Selamlar...
    Cisco 2500 Router 16 mb flash lı bir router a bir ios yukleyecem yaklasık
    12 mb fakat flash 8 li 2 partitiondan olusuyor gorunuyor yuklerken flash size exceded hatası alıyorum ne
    yapabilirim ?

+ Konuyu Cevapla

Bu Konuyu Paylaşın !

Bu Konuyu Paylaşın !

Yetkileriniz

  • Konu Acma Yetkiniz Yok
  • Cevap Yazma Yetkiniz Yok
  • Eklenti Yükleme Yetkiniz Yok
  • Mesajınızı Değiştirme Yetkiniz Yok