clear contr e1 0/0
yaptiktan sonra halen violation aliyorsan
fiziksel problem uzerinde durmak gerekir

farkli bi sdh port'u
yeni bir kablo cekilmesi gibi...




-----Original Message-----
From: AD [mailto:[email protected]]
Sent: Tuesday, November 23, 2004 11:32 AM
To: [email][email protected][/email]
Subject: [cisco-ttl] Cisco-1760-v : IOS: c1700-ipvoice-mz.123-4.T4.bin ;
CONTROLLER UPDOWN



Herkese merhaba ;



Bir ucta SDH arkasinda 1760-v uzerinde vwic-2mft-g703 ile diger uctaki SDH
arkasinda 2691 ve uzerinde vwic-1mft-g703 ile 2 mbps'lik LL baglanti yapmaya
calisiyorum.





2691 tarafinda bir problem olmadigini biliyorum , fakat 1760 tarafinda şu
hata mesajini aliyorum..



%CONTROLLER-5-UPDOWN: Controller E1 0/0, changed state to down (10 SES)
%LINK-5-CHANGED: Interface Serial0/0:0, changed state to reset
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0:0, changed
state to down
%CONTROLLER-5-UPDOWN: Controller E1 0/0, changed state to up
%LINK-3-UPDOWN: Interface Serial0/0:0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0:0, changed
state to up


sh controller , sh run ciktilari aşagida.



clock ile ilgili bir problem oldugunu zannediyorum , framing ile ugrastim
ama bir sonuca varamadim. belirli bir sure sonra serial interface line
protocol down oluyor.

sh controllers'ta linecode violation degerleri yuksek..



Yardimci olabilirseniz cok sevinirim.



Router#sh controllers e1 0/0

E1 0/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20030807, FPGA: 11

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

Data in current interval (477 seconds elapsed):

1420 Line Code Violations, 4960 Path Code Violations

463 Slip Secs, 0 Fr Loss Secs, 40 Line Err Secs, 0 Degraded Mins

455 Errored Secs, 0 Bursty Err Secs, 8 Severely Err Secs, 4 Unavail
Secs

Data in Interval 1:

289555 Line Code Violations, 18099 Path Code Violations

256 Slip Secs, 6 Fr Loss Secs, 178 Line Err Secs, 2 Degraded Mins

261 Errored Secs, 0 Bursty Err Secs, 64 Severely Err Secs, 8 Unavail
Secs

Data in Interval 2:

184401 Line Code Violations, 13028 Path Code Violations

55 Slip Secs, 0 Fr Loss Secs, 370 Line Err Secs, 6 Degraded Mins

334 Errored Secs, 0 Bursty Err Secs, 58 Severely Err Secs, 233 Unavail
Secs

Total Data (last 2 15 minute intervals):

473956 Line Code Violations, 31127 Path Code Violations,

311 Slip Secs, 6 Fr Loss Secs, 548 Line Err Secs, 8 Degraded Mins,

595 Errored Secs, 0 Bursty Err Secs, 122 Severely Err Secs, 241 Unavail
Secs



Router#sh run

Building configuration...



Current configuration : 923 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

tdm clock E1 0/0 data export line

voice-card 0

!

voice-card 1

!

no aaa new-model

ip subnet-zero

ip cef

!

controller E1 0/0

framing NO-CRC4

channel-group 0 timeslots 1-31 speed 64

!

controller E1 0/1

framing NO-CRC4

!

controller E1 1/0

framing NO-CRC4

!

!

!

interface FastEthernet0/0

ip address x.x.x.x 255.255.255.224

speed auto

!

interface Serial0/0:0

ip address x.x.x.x 255.255.255.252

encapsulation ppp

!

ip classless

ip route 0.0.0.0 0.0.0.0 FastEthernet0/0

no ip http server