controller e1 3/2 down problem
CLI Guru - Cisco Eğitim ve Danışmanlık Merkezi |

+ Konuyu Cevapla
Toplam 10 sonuçtan 1 ile 10 arasındakiler gösteriliyor.
controller e1 3/2 down problem

Merhaba, Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim.... Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli

  1. #1
    İsmail CAN Guest

    Standart controller e1 3/2 down problem

    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor.
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0

    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 239 Unavail Secs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 6:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 15:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 16:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,
    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077 Unavail Secs
    as5350#




    ---------------------------------
    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

  2. #2
    Devrim Yener KUCUK Guest

    Standart Re: controller e1 3/2 down problem

    Merhaba

    Layer 1 active degilse , controller'un DOWN olmasi normal.

    Baglantiyi (kabloyu) ve "ISDN Switchtype" i kontrol edin oncelikle.
    Router network olmayacak di mi ? ( simulate network yapilabilir, isdn protocol-emulate network)

    Layer 1 active olursa layer 2 icin (debug isdn q921 )...


    Kolay gelsin

    Devrim




    ----- Original Message -----
    From: İsmail CAN
    To: [email][email protected][/email]
    Sent: Monday, August 02, 2004 5:43 PM
    Subject: [cisco-ttl] controller e1 3/2 down problem


    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor.
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0

    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 239 UnavailSecs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 6:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 15:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 16:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,
    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077 Unavail Secs
    as5350#




    ------------------------------------------------------------------------------
    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bire-posta gönderebilirsiniz.


    Yahoo! Groups Sponsor
    ADVERTISEMENT





    ------------------------------------------------------------------------------
    Yahoo! Groups Links

    a.. To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    b.. To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service..




  3. #3
    Serhat Uslay Guest

    Standart Re: controller e1 3/2 down problem


    Daha once calistimi yoksa yeni bir duzenleme mi ??
    1) su dokumani bir oku.. [url]http://www.cisco.com/warp/public/116/T1_pri.html[/url]
    2) Eger cablo ve modem den eminsen, carrier ile konus..
    boyle bir cikti gormen lazim hersey duzgun ise
    RTDC05>sh isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial4/0/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x801F7FFF
    Number of L2 Discards = 0, L2 Session ID = 0

    Serhat


    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda
    gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli
    birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor..
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0
    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail
    Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail
    Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err! Secs, 239 Unavail
    Secs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail
    Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 6:
    0 Line Code Violati! ons, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Sec! s, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs! , 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail
    Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 15:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 16:
    0 Li! ne Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err ! Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Una! vail
    Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,
    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077
    Unavail Secs
    as5350#



    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir
    e-posta gönderebilirsiniz.



    Yahoo! Groups Sponsor

    ADVERTISEMENT
    click here

    [IMAGE]


    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






    ------------------------------------------------------------------------
    This email is intended for the named recipient only. The information
    contained in this message may be confidential, or commercially sensitive.
    If you are not the intended recipient you must not reproduce or
    distribute any part of the email, disclose its contents to any other
    party, or take any action in reliance on it. If you have received this
    email in error, please contact the sender immediately. Please delete
    this message from your computer.
    ------------------------------------------------------------------------

  4. #4
    İsmail CAN Guest

    Standart Re: controller e1 3/2 down problem

    Merhaba,

    Dun aksam hersey normaldi yani sh isdn status ve sh controllers e1 3/2 yaptıgımda hersey normaldi. Daha sonra aksam giderken gw kapattım bu sabah actim yine aynı problem Layer 1 Deactivated ve controller e1 3/2 down. Benim bu ise aklim ermedi. Sorun benim tarafta mi telekomda mi anlamadim. Telekomu ariyorum bizim tarafta hersey normal sizin tarafta sorun var diyorlar. Arkadaslar yardimci olabilirmisiniz. Tesekkurler...

    Serhat Uslay <[email protected]> wrote:

    Daha once calistimi yoksa yeni bir duzenleme mi ??
    1) su dokumani bir oku.. [url]http://www.cisco.com/warp/public/116/T1_pri.html[/url]
    2) Eger cablo ve modem den eminsen, carrier ile konus..
    boyle bir cikti gormen lazim hersey duzgun ise
    RTDC05>sh isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial4/0/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x801F7FFF
    Number of L2 Discards = 0, L2 Session ID = 0

    Serhat


    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor.
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0
    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, Line Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err! Secs, 239 Unavail Secs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 6:
    0 Line Code Violati! ons, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Sec! s, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs! , 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 15:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 16:
    0 Li! ne Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err ! Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Una! vail Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,
    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077 Unavail Secs
    as5350#


    ---------------------------------


    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir e-posta gönderebilirsiniz.


    Yahoo! Groups Sponsor
    ADVERTISEMENT
    click here


    [IMAGE]


    ---------------------------------

    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.




    ------------------------------------------------------------------------ This email is intended for the named recipient only. The information contained in this message may be confidential, or commercially sensitive. If you are not the intended recipient you must not reproduce or distribute any part of the email, disclose its contents to any other party, or take any action in reliance on it. If you have received this email in error, please contact the sender immediately. Please delete this message from your computer. ------------------------------------------------------------------------

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir e-posta gönderebilirsiniz.


    Yahoo! Groups SponsorADVERTISEMENT


    ---------------------------------
    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.



    ---------------------------------
    Do you Yahoo!?
    Yahoo! Mail - 50x more storage than other providers!

  5. #5
    Serhat Uslay Guest

    Standart Re: controller e1 3/2 down problem


    "gw kapattim" , niye GW 'yi kapatiyorsun ?? .. kapatmadan once bir
    degisiklik yapmadiysan calismasi lazim..
    tekrar boot ederken hic hata mesaji aldin mi ?
    eger kendi tarafindan emin sen Telekom'a bastir, loopback filan yapip
    kontrol etsinler...
    Serhat


    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: Re: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Dun aksam hersey normaldi yani sh isdn status ve sh controllers e1 3/2
    yaptıgımda hersey normaldi. Daha sonra aksam giderken gw kapattım bu sabah
    actim yine aynı problem Layer 1 Deactivated ve controller e1 3/2 down.
    Benim bu ise aklim ermedi. Sorun benim tarafta mi telekomda mi anlamadim.
    Telekomu ariyorum bizim tarafta hersey normal sizin tarafta sorun var
    diyorlar. Arkadaslar yardimci olabilirmisiniz. Tesekkurler...

    Serhat Uslay <[email protected]> wrote:

    Daha once calistimi yoksa yeni bir duzenleme mi ??
    1) su dokumani bir oku.. [url]http://www.cisco.com/warp/public/116/T1_pri.html[/url]
    2) Eger cablo ve modem den eminsen, carrier ile konus..
    boyle bir cikti gormen lazim hersey duzgun ise
    RTDC05>sh isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial4/0/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    ! ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x801F7FFF
    Number of L2 Discards = 0, L2 Session ID = 0

    Serhat

    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda
    gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli
    birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor..
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0ONT>
    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, L! ine Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail
    Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail
    Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations!
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err! Secs, 239 Unavail
    Secs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail
    Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 6:
    0 Line Code Violati! ons, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr L! oss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Sec! s, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs! , 0 Severely Err Secs, 900 Unavail
    Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail
    Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 15:
    0 Line Code Violat! ions, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 16:
    0 Li! ne Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely E! rr Secs, 0 Unavail
    Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err ! Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 F! r Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Una! vail
    Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    &nbs! p; 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0
    Unavail Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail
    Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,

    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077
    Unavail Secs
    as5350#




    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir
    e-posta gönderebilirsiniz.



    Yahoo! Groups Sponsor

    ADVERTISEMENT
    click here

    [IMAGE]



    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






    ------------------------------------------------------------------------
    This email is intended for the named recipient only. The information
    contained in this message may be confidential, or commercially sensitive.
    If you are not the intended recipient you must not reproduce or distribute
    any part of the email, disclose its contents to any other party, or take
    any action in reliance on it. If you have received this email in error,
    please contact the sender immediately. Please delete this message from
    your computer.
    ------------------------------------------------------------------------

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir
    e-posta gönderebilirsiniz.



    Do you Yahoo!?
    Yahoo! Mail - 50x more storage than other providers!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir
    e-posta gönderebilirsiniz.



    Yahoo! Groups Sponsor

    ADVERTISEMENT
    click here

    [IMAGE]


    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






    ------------------------------------------------------------------------
    This email is intended for the named recipient only. The information
    contained in this message may be confidential, or commercially sensitive.
    If you are not the intended recipient you must not reproduce or
    distribute any part of the email, disclose its contents to any other
    party, or take any action in reliance on it. If you have received this
    email in error, please contact the sender immediately. Please delete
    this message from your computer.
    ------------------------------------------------------------------------

  6. #6
    İsmail CAN Guest

    Standart Re: controller e1 3/2 down problem

    Merhaba,

    Suan gw yi sadece PRI icin kullancam o yuzden aktif olmadıgı icin kapattim. Ama kesinlike ne fiziksel baglantıda ne de configte degisiklik yaptım. Configi save ettim copy run startup, sabah geldigimde de tek yaptıgım acmak oldu. Modem uzerindeki ledlere gore hersey normal gorunuyor. Ancak gw de yine aynı problemler. Telekomu aradım burdan hersey normal gorunuyor diyorlar.
    Nasıl bir yol izlemeliyim. Tesekkurler


    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0

    Serhat Uslay <[email protected]> wrote:

    "gw kapattim" , niye GW 'yi kapatiyorsun ?? .. kapatmadan once bir degisiklik yapmadiysan calismasi lazim..
    tekrar boot ederken hic hata mesaji aldin mi ?
    eger kendi tarafindan emin sen Telekom'a bastir, loopback filan yapip kontrol etsinler...
    Serhat


    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: Re: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Dun aksam hersey normaldi yani sh isdn status ve sh controllers e1 3/2 yaptıgımda hersey normaldi. Daha sonra aksam giderken gw kapattım bu sabah actim yine aynı problem Layer 1 Deactivated ve controller e1 3/2 down. Benim bu ise aklim ermedi. Sorun benim tarafta mi telekomda mi anlamadim. Telekomu ariyorum bizim tarafta hersey normal sizin tarafta sorun var diyorlar. Arkadaslar yardimci olabilirmisiniz. Tesekkurler...

    Serhat Uslay <[email protected]> wrote:

    Daha once calistimi yoksa yeni bir duzenleme mi ??
    1) su dokumani bir oku.. [url]http://www.cisco.com/warp/public/116/T1_pri.html[/url]
    2) Eger cablo ve modem den eminsen, carrier ile konus..
    boyle bir cikti gormen lazim hersey duzgun ise
    RTDC05>sh isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial4/0/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    ! ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x801F7FFF
    Number of L2 Discards = 0, L2 Session ID = 0

    Serhat

    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor.
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0ONT>
    "sh controllers e1 3/2 "

    as5350#sh controllers e1 3/2
    E1 3/2 is down.
    Applique type is Channelized E1 - balanced
    Far End Block Errors Detected
    Receiver has loss of signal.
    alarm-trigger is not set
    Version info of slot 3: HW: 519, PLD Rev: 1
    Framer Version: 0x8
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x05,
    Board Hardware Version 2.7, Item Number 73-5267-03,
    Board Revision A0, Serial Number JAE08083CU8,
    PLD/ISP Version <unset>, Manufacture Date 22-Feb-2004.
    Framing is CRC4, L! ine Code is HDB3, Clock Source is Line.
    Data in current interval (273 seconds elapsed):
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 273 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 273 Unavail Secs
    Data in Interval 1:
    344020 Line Code Violations, 61147 Path Code Violations
    1 Slip Secs, 660 Fr Loss Secs, 84 Line Err Secs, 0 Degraded Mins
    1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 693 Unavail Secs
    Data in Interval 2:
    226022 Line Code Violations, 29065 Path Code Violations!
    0 Slip Secs, 229 Fr Loss Secs, 37 Line Err Secs, 0 Degraded Mins
    5 Errored Secs, 3 Bursty Err Secs, 17 Severely Err! Secs, 239 Unavail Secs
    Data in Interval 3:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 897 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 897 Unavail Secs
    Data in Interval 4:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 5:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 6:
    0 Line Code Violati! ons, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 7:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr L! oss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 8:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 9:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Sec! s, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 10:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 11:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 12:
    16384908 Line Code Violations, 196475 Path Code Violations
    244 Slip Secs, 850 Fr Loss Secs, 399 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs! , 0 Severely Err Secs, 900 Unavail Secs
    Data in Interval 13:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 148 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 148 Unavail Secs
    Data in Interval 14:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 15:
    0 Line Code Violat! ions, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 16:
    0 Li! ne Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 17:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely E! rr Secs, 0 Unavail Secs
    Data in Interval 18:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 19:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err ! Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 20:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 F! r Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 21:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 22:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Una! vail Secs
    Data in Interval 23:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 24:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 25:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    &nbs! p; 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Data in Interval 26:
    0 Line Code Violations, 0 Path Code Violations
    0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
    0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Total Data (last 26 15 minute intervals):
    16954950 Line Code Violations, 286687 Path Code Violations,
    245 Slip Secs, 9984 Fr Loss Secs, 520 Line Err Secs, 0 Degraded Mins,
    6 Errored Secs, 3 Bursty Err Secs, 17 Severely Err Secs, 10077 Unavail Secs
    as5350#


    ---------------------------------



    Do you Yahoo!?
    New and Improved Yahoo! Mail - 100MB free storage!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir e-posta gönderebilirsiniz.


    Yahoo! Groups Sponsor
    ADVERTISEMENT
    click here


    [IMAGE]

    ---------------------------------



    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.





    ------------------------------------------------------------------------ This email is intended for the named recipient only. The information contained in this message may be confidential, or commercially sensitive. If you are not the intended recipient you must not reproduce or distribute any part of the email, disclose its contents to any other party, or take any action in reliance on it. If you have received this email in error, please contact the sender immediately. Please delete this message from your computer. ------------------------------------------------------------------------

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir e-posta gönderebilirsiniz.

    ---------------------------------



    Do you Yahoo!?
    Yahoo! Mail - 50x more storage than other providers!

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email][email protected][/email] adresine bir e-posta gönderebilirsiniz.


    Yahoo! Groups Sponsor
    ADVERTISEMENT
    click here


    [IMAGE]


    ---------------------------------

    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.




    ------------------------------------------------------------------------ This email is intended for the named recipient only. The information contained in this message may be confidential, or commercially sensitive. If you are not the intended recipient you must not reproduce or distribute any part of the email, disclose its contents to any other party, or take any action in reliance on it. If you have received this email in error, please contact the sender immediately. Please delete this message from your computer. ------------------------------------------------------------------------

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için [email]cisco-ttl[email protected][/email] adresine bir e-posta gönderebilirsiniz.


    Yahoo! Groups SponsorADVERTISEMENT


    ---------------------------------
    Yahoo! Groups Links

    To visit your group on the web, go to:
    [url]http://groups.yahoo.com/group/cisco-ttl/[/url]

    To unsubscribe from this group, send an email to:
    [email][email protected][/email]

    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.



    ---------------------------------
    Do you Yahoo!?
    Yahoo! Mail Address AutoComplete - You start. We finish.

  7. #7
    Serhat Uslay Guest

    Standart Re: controller e1 3/2 down problem

    once bunu takip edip sonuclarini buraya yolla, bu chart'a gore telco
    hatasi gorunuyor..


    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: Re: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Suan gw yi sadece PRI icin kullancam o yuzden aktif olmadıgı icin
    kapattim. Ama kesinlike ne fiziksel baglantıda ne de configte degisiklik
    yaptım. Configi save ettim copy run startup, sabah geldigimde de tek
    yaptıgım acmak oldu. Modem uzerindeki ledlere gore hersey normal
    gorunuyor. Ancak gw de yine aynı problemler. Telekomu aradım burdan hersey
    normal gorunuyor diyorlar.
    Nasıl bir yol izlemeliyim. Tesekkurler


    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0

    Serhat Uslay <[email protected]> wrote:

    "gw kapattim" , niye GW 'yi kapatiyorsun ?? .. kapatmadan once bir
    degisiklik yapmadiysan calismasi lazim..
    tekrar boot ederken hic hata mesaji aldin mi ?
    eger kendi tarafindan emin sen Telekom'a bastir, loopback filan yapip
    kontrol etsinler...
    Serhat

    Please respond to [email][email protected][/email]

    To: [email][email protected][/email]
    cc:
    Subject: Re: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Dun aksam hersey normaldi yani sh isdn status ve sh controllers e1 3/2
    yaptıgımda hersey normaldi. Daha sonra aksam giderken gw kapattım bu sabah
    actim yine aynı problem Layer 1 Deactivated ve controller e1 3/2 down.
    Benim bu ise aklim ermedi. Sorun benim tarafta mi telekomda mi anlamadim.
    Telekomu ariyorum bizim tarafta hersey normal sizin tarafta sorun var
    diyorlar. Arkadaslar yardimci olabilirmisiniz. Tesekkurler...

    Serhat Uslay <[email protected]> wrote:

    Daha once calistimi yoksa yeni bir duzenleme mi ??
    1) su dokumani bir oku.. [url]http://www.cisco.com/warp/public/116/T1_pri.html[/url]
    2) Eger cablo ve modem den eminsen, carrier ile konus..
    boyle bir cikti gormen lazim hersey duzgun ise
    RTDC05>sh isdn stat
    Global ISDN Switchtype = primary-net5
    ISDN Serial4/0/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    ! ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x801F7FFF
    Number of L2 Discards = 0, L2 Session ID = 0

    Serhat

    Please respond to [email][email protected][/email]NT>

    To: [email][email protected][/email]
    cc:
    Subject: [cisco-ttl] controller e1 3/2 down problem



    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda
    gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli
    birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor..

  8. #8
    İsmail CAN Guest

    Standart PRI problem

    Merhabalar,

    Bir adet PRI baglantim var ve origination scenaryousnu deniyorum. Termination denemesi basarili ama originde asagidaki hata var. yorumu olan arkadaslar varsa cok sevinirim. Tesekkurler

    debug q931 ve 921
    as5350#
    Jan 1 05:22:42.242: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=93
    Jan 1 05:22:42.250: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=116
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=93 nr=116
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q931: SETUP pd = 8 callref = 0x1140
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA98387
    Exclusive, Channel 7
    Progress Ind i = 0x8283 - Origination address is non-ISDN
    Calling Party Number i = 0x0183, '03122310354'
    Plan:ISDN, Type:Unknown
    Called Party Number i = 0xC1, '2943050'
    Plan:ISDN, Type:Subscriber(local)
    Sending Complete
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=94
    Jan 1 05:22:43.154: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2D calltype 2 CALL_INCOMING
    Jan 1 05:22:43.158: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=116 nr=94
    Jan 1 05:22:43.158: ISDN Se3/2:15 Q931: CALL_PROC pd = 8 callref = 0x9140
    Channel ID i = 0xA18387
    Preferred, Channel 7
    Jan 1 05:22:43.158: ISDN Se3/2:15 **ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0
    Jan 1 05:22:43.162: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=117 nr=94
    Jan 1 05:22:43.162: ISDN Se3/2:15 Q931: DISCONNECT pd = 8 callref = 0x9140
    Cause i = 0x80AC - Requested circuit/channel not available
    Jan 1 05:22:43.170: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=117
    Jan 1 05:22:43.174: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=118
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=94 nr=118
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q931: RELEASE pd = 8 callref = 0x1140
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=95
    Jan 1 05:22:43.302: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2D calltype 2 CALL_CLEARED
    Jan 1 05:22:43.302: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=118 nr=95
    Jan 1 05:22:43.302: ISDN Se3/2:15 Q931: RELEASE_COMP pd = 8 callref = 0x9140
    Jan 1 05:22:43.310: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=119
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=95 nr=119
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q931: SETUP pd = 8 callref = 0x0503
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA98388
    Exclusive, Channel 8
    Progress Ind i = 0x8283 - Origination address is non-ISDN
    Calling Party Number i = 0x0183, '03122456789'
    Plan:ISDN, Type:Unknown
    Called Party Number i = 0xC1, '3256780'
    Plan:ISDN, Type:Subscriber(local)
    Sending Complete
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=96
    Jan 1 05:22:43.654: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2E calltype 2 CALL_INCOMING
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=119 nr=96
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q931: CALL_PROC pd = 8 callref = 0x8503
    Channel ID i = 0xA18388
    Preferred, Channel 8
    Jan 1 05:22:43.658: ISDN Se3/2:15 **ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=120 nr=96
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q931: DISCONNECT pd = 8 callref = 0x8503
    Cause i = 0x80AC - Requested circuit/channel not available
    Jan 1 05:22:43.666: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=120
    Jan 1 05:22:43.670: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=121
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=96 nr=121
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q931: RELEASE pd = 8 callref = 0x0503
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=97
    Jan 1 05:22:43.750: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2E calltype 2 CALL_CLEARED
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=121 nr=97
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q931: RELEASE_COMP pd = 8 callref = 0x8503
    Jan 1 05:22:43.758: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=122
    Jan 1 05:22:53.758: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=97
    Jan 1 05:22:53.766: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=122
    Jan 1 05:23:03.766: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=97
    Jan 1 05:23:03.774: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=122
    Jan 1 05:23:04.114: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not half duplex), with SEP000B465DAE28 Port 1 (half duplex).


    Devrim Yener KUCUK <[email protected]> wrote:Merhaba

    Layer 1 active degilse , controller'un DOWN olmasi normal.

    Baglantiyi (kabloyu) ve "ISDN Switchtype" i kontrol edin oncelikle.
    Router network olmayacak di mi ? ( simulate network yapilabilir, isdn protocol-emulate network)

    Layer 1 active olursa layer 2 icin (debug isdn q921 )...


    Kolay gelsin

    Devrim




    ----- Original Message -----
    From: İsmail CAN
    To: [email][email protected][/email]
    Sent: Monday, August 02, 2004 5:43 PM
    Subject: [cisco-ttl] controller e1 3/2 down problem


    Merhaba,

    Arkadaslar bu konuda yardımcı olursanız cok sevinirim. Lutfen bu konuda gercekten yardıma ihtiycım var. Cok tesekkur ederim....


    Layer 1 active hale getiremiyorum alcatel hdsl 1512 modem ile as5350 bagli birbirine,
    aynı zamanda "sh controllers e1 3/2" yaptıgımda e1 3/2 down gorunuyor.
    "sh isdn status"
    as5350#sh isdn status
    Global ISDN Switchtype = primary-net5
    ISDN Serial3/2:15 interface
    dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
    DEACTIVATED
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 98
    Total Allocated ISDN CCBs = 0

  9. #9
    Devrim Yener KUCUK Guest

    Standart Re: PRI problem

    Merhaba,

    Bu bilinen bi hata mesaji:

    "**ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0"

    Once

    sh ver,
    sh run,
    sh isdn stat,

    alalim



    Devrim

    ----- Original Message -----
    From: İsmail CAN
    To: [email][email protected][/email]
    Sent: Tuesday, August 03, 2004 3:17 PM
    Subject: [cisco-ttl] PRI problem


    Merhabalar,

    Bir adet PRI baglantim var ve origination scenaryousnu deniyorum. Termination denemesi basarili ama originde asagidaki hata var. yorumu olan arkadaslar varsa cok sevinirim. Tesekkurler

    debug q931 ve 921
    as5350#
    Jan 1 05:22:42.242: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=93
    Jan 1 05:22:42.250: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=116
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=93 nr=116
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q931: SETUP pd = 8 callref = 0x1140
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA98387
    Exclusive, Channel 7
    Progress Ind i = 0x8283 - Origination address is non-ISDN
    Calling Party Number i = 0x0183, '03122310354'
    Plan:ISDN, Type:Unknown
    Called Party Number i = 0xC1, '2943050'
    Plan:ISDN, Type:Subscriber(local)
    Sending Complete
    Jan 1 05:22:43.154: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=94
    Jan 1 05:22:43.154: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2D calltype 2 CALL_INCOMING
    Jan 1 05:22:43.158: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=116 nr=94
    Jan 1 05:22:43.158: ISDN Se3/2:15 Q931: CALL_PROC pd = 8 callref = 0x9140
    Channel ID i = 0xA18387
    Preferred, Channel 7
    Jan 1 05:22:43.158: ISDN Se3/2:15 **ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0
    Jan 1 05:22:43.162: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=117 nr=94
    Jan 1 05:22:43.162: ISDN Se3/2:15 Q931: DISCONNECT pd = 8 callref =0x9140
    Cause i = 0x80AC - Requested circuit/channel not available
    Jan 1 05:22:43.170: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=117
    Jan 1 05:22:43.174: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=118
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=94 nr=118
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q931: RELEASE pd = 8 callref = 0x1140
    Jan 1 05:22:43.298: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=95
    Jan 1 05:22:43.302: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2D calltype 2 CALL_CLEARED
    Jan 1 05:22:43.302: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=118 nr=95
    Jan 1 05:22:43.302: ISDN Se3/2:15 Q931: RELEASE_COMP pd = 8 callref = 0x9140
    Jan 1 05:22:43.310: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=119
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=95 nr=119
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q931: SETUP pd = 8 callref = 0x0503
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA98388
    Exclusive, Channel 8
    Progress Ind i = 0x8283 - Origination address is non-ISDN
    Calling Party Number i = 0x0183, '03122456789'
    Plan:ISDN, Type:Unknown
    Called Party Number i = 0xC1, '3256780'
    Plan:ISDN, Type:Subscriber(local)
    Sending Complete
    Jan 1 05:22:43.654: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=96
    Jan 1 05:22:43.654: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2E calltype 2 CALL_INCOMING
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=119 nr=96
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q931: CALL_PROC pd = 8 callref = 0x8503
    Channel ID i = 0xA18388
    Preferred, Channel 8
    Jan 1 05:22:43.658: ISDN Se3/2:15 **ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=120 nr=96
    Jan 1 05:22:43.658: ISDN Se3/2:15 Q931: DISCONNECT pd = 8 callref =0x8503
    Cause i = 0x80AC - Requested circuit/channel not available
    Jan 1 05:22:43.666: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=120
    Jan 1 05:22:43.670: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=121
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User RX <- INFO sapi=0 tei=0, ns=96 nr=121
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q931: RELEASE pd = 8 callref = 0x0503
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User TX -> RR sapi=0 tei=0 nr=97
    Jan 1 05:22:43.750: ISDN Se3/2:15 EVENT: process_rxstate: ces/callid 1/0x2E calltype 2 CALL_CLEARED
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q921: User TX -> INFO sapi=0 tei=0, ns=121 nr=97
    Jan 1 05:22:43.750: ISDN Se3/2:15 Q931: RELEASE_COMP pd = 8 callref = 0x8503
    Jan 1 05:22:43.758: ISDN Se3/2:15 Q921: User RX <- RR sapi=0 tei=0 nr=122
    Jan 1 05:22:53.758: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=97
    Jan 1 05:22:53.766: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=122
    Jan 1 05:23:03.766: ISDN Se3/2:15 Q921: User TX -> RRp sapi=0 tei=0 nr=97
    Jan 1 05:23:03.774: ISDN Se3/2:15 Q921: User RX <- RRf sapi=0 tei=0 nr=122
    Jan 1 05:23:04.114: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not half duplex), with SEP000B465DAE28 Port 1 (half duplex).




  10. #10
    İsmail CAN Guest

    Standart Re: PRI problem

    Merhaba,

    tahsis edilen numaralar: 2456000-2456049 olarak dusunun aradıgım numara 2456000 ama olmuyor.:(

    sh sonucları asagida
    Tesekkurler...

    Devrim Yener KUCUK <[email protected]> wrote:
    Merhaba,

    Bu bilinen bi hata mesaji:

    "**ERROR**: isdn_cdapi_callback_from_rm: RM returned Reject, call_type 1 resource type 0"

    Once

    sh ver,
    sh run,
    sh isdn stat,

    alalim

    Devrim

+ Konuyu Cevapla

Bu Konuyu Paylaşın !

Bu Konuyu Paylaşın !

Yetkileriniz

  • Konu Acma Yetkiniz Yok
  • Cevap Yazma Yetkiniz Yok
  • Eklenti Yükleme Yetkiniz Yok
  • Mesajınızı Değiştirme Yetkiniz Yok